SSC200

Which NMEA 0183 sentences does the SSC200 transmit?

Jun 17, 2008 0 0 5485 0/5 (0 Vote)

The SSC200 transmits the following NMEA 0183 sentences or messages: HDG - Heading, Deviation & Variation HDM - Heading, Magnetic HDT - Heading, True ROT - Rate of Turn MAROUT - Maretron Proprietary Output Sentence Read More

I see that Maretron’s DSM150, DSM200, and DSM250 displays have a SSC200 configuration setting called "Rate of Turn Damping Period:"; what is this?

Jun 19, 2008 0 0 6135 0/5 (0 Vote)

Maretron's DSM150, DSM200, and DSM250 displays have a SSC200 configuration setting called "Rate of Turn Damping Period:", which is used to smooth the rate of turn indication. The rate of turn indication uses the rate of turn gyro found within the... Read More

I see that Maretron’s DSM150, DSM200, and DSM250 displays have a SSC200 configuration setting called "Rate of Turn Zero Offset Calibration..."; what is this?

Jul 19, 2008 0 0 5934 0/5 (0 Vote)

Maretron's DSM150, DSM200, and DSM250 displays have a SSC200 configuration setting called "Rate of Turn Zero Offset Calibration...", which is used to calibrate the rate of turn gyro found within the SSC200. Rate gyros tend to drift over temperature ... Read More

What are the approximate dimensions of the SSC200?

Jun 19, 2008 0 0 4193 0/5 (0 Vote)

The SSC200 is approximately 2.05" tall and 3.25" in length and width not including the supplied the mounting brackets. Read More

I see that Maretron’s DSM150, DSM200, and DSM250 displays have a SSC200 configuration setting called "Invert Installation:"; what is this?

Jun 17, 2008 0 0 5931 0/5 (0 Vote)

Maretron's DSM150, DSM200, and DSM250 displays have a SSC200 configuration setting called "Invert Installation:", which is used to describe the orientation of the compass relative to the vessel. For example, the compass can be mounted upside down on... Read More

I see that Maretron’s DSM150, DSM200, and DSM250 displays have a SSC200 configuration setting called "Installation Offset Calibration?"; what is this?

Jun 19, 2008 0 0 6089 0/5 (0 Vote)

Maretron'sDSM150, DSM200, and DSM250 displays have a SSC200 configuration setting called "Installation Offset Calibration...", which is used to electronically align the compass with the vessel. Although there is an arrow on the compass label, it is... Read More

I see that Maretron’s DSM150, DSM200, and DSM250 displays have a SSC200 configuration setting called "Magnetic Deviation Status?"; what is this?

Jun 19, 2008 0 0 5867 0/5 (0 Vote)

Maretron's DSM150, DSM200, and DSM250 displays have a SSC200 configuration setting called "Magnetic Deviation Status...", which is used to display information about the deviation table that was stored within the compass when the compass was last... Read More

How do I calibrate the SSC200 to account for magnetic deviation?

Jul 19, 2008 0 0 4944 0/5 (0 Vote)

The SSC200 can be calibrated to account for magnetic deviation in several ways; please refer to the SSC200 User's Manual for instructions. It is always best to calibrate the rate of turn gyro before you perform magnetic deviation calibration on the... Read More

I see that Maretron’s DSM150, DSM200, and DSM250 displays have a SSC200 configuration setting called "Magnetic Deviation Calibration?"; what is this?

Jun 19, 2008 0 0 6027 0/5 (0 Vote)

Maretron's DSM150, DSM200, and DSM250 displays have a SSC200 configuration setting called "Magnetic Deviation Calibration...", which is used to calibrate the compass to account for sources of magnetic deviation on the vessel. Read More

I see that Maretron’s DSM150, DSM200, and DSM250 displays have a SSC200 configuration setting called "Variation Source:"; what is this?

Jun 19, 2008 0 0 6154 0/5 (0 Vote)

Maretron's DSM150, DSM200, and DSM250 displays have a SSC200 configuration setting called "Variation Source:", which is used to tell the compass from where it should receive the magnetic variation for subsequent transmission of the heading (HDT)... Read More

Results 31 - 40 of 55