RIM100

What firmware changes have taken place on the Maretron RIM100?

Aug 29, 2013 RIM100, history, changes 0 0 3902 0/5 (0 Vote)

What firmware changes have taken place on the Maretron RIM100? Update your device using the N2KAnalyzer software tool. RIM100 Firmware Versions 1.2.1.1 (2015-10-01) Manufacturing Improvements 1.1.4.3 (2013-07-19) Added support... Read More

Can you mix AC and DC loads on the same RIM100?

Nov 6, 2019 RIM100, AC, DC 0 0 2051 0/5 (0 Vote)

Yes, each channel is optically isolated allowing the end users to “mix and match” the load types you are interested in monitoring. Please take note of the proper wiring installation for both the AC and DC load connections. ... Read More

Using N2KAnalyzer, how do I recover a Maretron device?

Dec 22, 2011 N2KAnalyzer software 0 0 10566 2/5 (1 Vote)

Occasionally, a device can be in "boot mode" (represented in N2KAnalyzer by an orange highlight of the device's entry in the device list). This can happen due to a software update which fails due to network problems. A Maretron device that is ... Read More

Can Maretron’s sensor data be displayed on a Furuno CANBUS network?

Jun 12, 2017 0 0 7838 1/5 (1 Vote)

Yes, much of Maretron device's data can be shown on Furuno displays with “CANBUS” functionality. Firstly, Maretron recommends that customers verify device compatibility by reviewing the Maretron product's datasheet specifically,... Read More

What type of information can be viewed on Maretron’s display products, and what products are required to generate the data to be displayed?

Oct 25, 2011 0 0 40119 0/5 (0 Vote)

The Maretron Capability Matrix helps highlight the system features available for display when designing a system within N2KBuilder. To generate a system capability Matrix within N2KBuilder simply click on Tools, "Create Maretron Capability... Read More

What are the voltage specifications for each Maretron device?

Dec 22, 2011 0 0 14820 5/5 (1 Vote)

Maretron Model Device Description NMEA2000 Operating Voltage Engine/Battery Interface CLM100 P/N: M000070 Current Loop Monitor 9 to 32 Volts SSC200 P/N: M000001, M000021, M000022 NMEA 2000 Solid State Compass HW 1.0 9 to 16 Volts ... Read More

What is the SMS100 Status message? Which Maretron components do I need?

Jun 6, 2013 0 0 7628 0/5 (0 Vote)

The SMS100 Status Message is a text message you can receive from the SMS100 containing key pieces of information regarding your vessel. When the SMS100 is installed, you can text the word "Status" to your SMS100 cellular number ... Read More

I see N2KView offers a component for "Indicator Status"; what products can I use to show Indicator Status?

Mar 27, 2015 Indicators, RIM100, SIM100, DCR100, Bilge, Smoke, CO, Overlay, Fire Alarms, Safety, Warnings, Alarms, Light panel 0 0 5260 0/5 (0 Vote)

An Indicator Status component uses the NMEA 2000 message called "Binary Switch Bank Status" to show three condition states: On Off Error A RIM100, SIM100, and DCR100 all transmit the necessary message for the N2KView component to work. You can create... Read More

How do I show simple bilge information on Mareton’s DSM150 or DSM250 displays?

Apr 27, 2013 0 0 8268 0/5 (0 Vote)

Knowldege base article 578 showed how to do simple bilge monitoring using Maretron's Run Indicator Module (RIM100). This article shows how the monitored information from article 578 can be displayed on Maretron's DSM150 and DSM250 displays. The left... Read More

How do I monitor the bilge with Maretron equipment?

Apr 20, 2013 Bilge, Bilge Monitoring, Bilge Monitoring and control, High Water Monitoring, Bilge High water, Bilge high water alarm system 0 0 13617 3.67/5 (3 Votes)

Before we discuss how to monitor the bilge with Maretron equipment, let's take a look at a typical bilge pump and alarm wiring diagram (see Figure 1). Notice that there are two ways to turn the bilge pump on. First, there is the float switch -- when... Read More

Results 1 - 10 of 13