SSC200

How do I display the SSC200 magnetic heading on Maretron’s DSM150, DSM200, or DSM250 display?

Jul 22, 2008 0 0 6334 0/5 (0 Vote)

You display the SSC200 magnetic heading information on a DSM150, DSM200, or DSM250 in the following way: Enter menu mode, scroll to "Favorite Screen Setup..." and press Scroll to the favorite screen where you would like to view the magnetic heading... Read More

I navigate using magnetic heading and not true heading; how do I use the SSC200 compass and Maretron’s DSM150, DSM200, or DSM250 display to view my heading in magnetic?

Jun 19, 2008 0 0 6530 0/5 (0 Vote)

The SSC200 compass outputs heading information in magnetic format, so you just need to properly configure the DSM150, DSM200, or DSM250 to display heading in magnetic. To view magnetic heading on the DSM150, DSM200, or DSM250, do the following: Enter... Read More

What is the maximum rate at which the SSC200 will transmit heading from the NMEA 0183 port?

Jun 19, 2008 0 0 4902 0/5 (0 Vote)

By default, the SSC200 transmits heading from the NMEA 0183 interface ten times per second. This can be changed to 40 times per second in one of two ways: 1) using Maretron's DSM150, DSM200, or DSM250 display (please see the respective display's user... Read More

What is the maximum rate at which the SSC200 will transmit heading from the NMEA 2000 port?

Jun 19, 2008 0 0 4315 0/5 (0 Vote)

The SSC200 transmits heading 10 times per second via the NMEA 2000 port. Read More

I see that Maretron’s DSM150, DSM200, and DSM250 displays have a SSC200 configuration setting called "Reset Factory Defaults"; what is this?

Jul 21, 2008 0 0 6174 0/5 (0 Vote)

Maretron's DSM150, DSM200, and DSM250 displays have a SSC200 configuration setting called "Reset Factory Defaults", which is used to return the SSC200 to its factory settings. Resetting the SSC200 erases the deviation table, clears the installation... Read More

I see that Maretron’s DSM150 and DSM250 displays have a SSC200 configuration setting called "NMEA 2000 PGN Enable/Disable..."; what is this?

Jun 19, 2008 0 1 5816 0/5 (0 Vote)

Maretron's DSM150 and DSM250 displays have a SSC200 configuration setting called "NMEA 2000 PGN Enable/Disable:", which is used to turn on and off specific NMEA 2000 messages that are transmitted by the SSC200. Read More

I see the SSC200 uses the NMEA 0183 identifier II (i.e., the two letters following the $ of an NMEA 0183 sentence); is it possible to change the identifier to some other value?

Jun 17, 2008 0 0 4431 0/5 (0 Vote)

Yes, it is possible to change the identifier that the SSC200 transmits as part of NMEA 0183 sentences. Please refer to the user's manual for instructions on how to make this change. Read More

Is it possible to change the baud rate of the SSC200 NMEA 0183 port?

Jun 15, 2010 0 0 8808 0/5 (0 Vote)

Yes, the baud rate can be changed from the default rate of 4800 baud to 38,400 baud. Please refer to the user's manual for changing the baud rate. Read More

What is the baud rate of the SSC200 NMEA 0183 port?

Jun 17, 2008 0 0 5987 0/5 (0 Vote)

The default baud rate of the SSC200 NMEA 0183 port is 4800 baud. This can be changed to 38,400 baud if desired. Read More

Which NMEA 0183 sentences does the SSC200 receive?

Jul 18, 2008 0 0 4584 0/5 (0 Vote)

The SSC200 receives the following NMEA0183 sentences or messages: RMC - Recommended Minimum Specific GNSS Data VTG - Course Over Ground and Ground Speed PMAREXE - Maretron Proprietary Execute Sentence PMARSETPX - Maretron Proprietary Set Period... Read More

Results 21 - 30 of 55