RAA100

Why doesn’t my rudder display read hard over when the rudder is hard over?

Jul 10, 2008 0 0 5003 0/5 (0 Vote)

The rudder display may not read hard over even though the rudder is hard over if the resistive sensor is not turning throughout its entire range. You can fix this by either adjusting the resistive sensor to turn across its entire range or you can... Read More

Is it possible to turn on or off RAA100 transmitted messages (or PGNs)?

Jul 11, 2008 0 0 4457 0/5 (0 Vote)

Yes, it is possible to turn on and off the RAA100 transmitted messages (or PGNs) using Mareton's DSM150, DSM200, or DSM250 display. On the display, enter menu mode, scroll to "Configuration…" and press enter. Scroll to "Device Configuration... Read More

How do I set the RAA100 configuration setting called "Gauge Resistance, + to sender" using Maretron’s DSM150, DSM200, or DSM250 display?

Jul 11, 2008 0 0 4802 0/5 (0 Vote)

You set the RAA100 "Gauge Resistance, + to sender" using Maretron's DSM150, DSM200, or DSM250 display in the following way. Enter menu mode, scroll to "Configuration…" and press enter. Scroll to "Device Configuration…" and press enter.... Read More

Can I set the RAA100 to accept the American standard for resistance values (i.e. 240 to 33 ohms) using Maretron’s DSM150, DSM200, or DSM250 display?

Jul 11, 2008 0 0 4907 0/5 (0 Vote)

Yes, it is possible to set the RAA100 to accept American standard resistive sensors using Maretron's DSM150, DSM200, or DSM250 display. Set the mode using Maretron's DSM150, DSM200, or DSM250 display in the following way. Enter menu mode, scroll to ... Read More

How do I reset the RAA100 to send the factory default messages (or PGNs)?

Jul 11, 2008 0 0 4484 0/5 (0 Vote)

You reset the RAA100 to transmit the factory default messages using Maretron's DSM250 display in the following way. Enter menu mode, scroll to "Configuration…" and press enter. Scroll to "Device Configuration…" and press enter. Scroll... Read More

How do I set the RAA100 rudder number or instance using Maretron’s DSM150, DSM200, or DSM250 display?

Jul 10, 2008 0 0 6954 0/5 (0 Vote)

You set the RAA100 rudder number or instance using Maretron's DSM150, DSM200, or DSM250 display in the following way. Enter menu mode, scroll to "Configuration…" and press enter. Scroll to "Device Configuration…" and press enter. Scroll... Read More

Can I custom calibrate the RAA100 for non-standard resistance sensors or can I do custom calibration for hard over points other than 60 degrees?

Jul 10, 2008 0 0 3872 0/5 (0 Vote)

Yes, it is possible to calibrate the RAA100 to accept non-standard resistive sensors or to set custom hard over angles using Maretron's DSM150, DSM200, or DSM250 display. Set the mode using Maretron's DSM150, DSM200, or DSM250 display in the... Read More

How do I display the RAA100 rudder angle on Maretron’s DSM150, DSM200, or DSM250 display?

Jul 10, 2008 0 0 8034 0/5 (0 Vote)

You display the RAA100 rudder angle on a DSM150, DSM200, or DSM250 in the following way. Enter menu mode, scroll to "Favorite Screen Setup..." and press enter. Scroll to the favorite screen where you would like to view the rudder angle and press... Read More

Can I set the RAA100 to accept the European standard for resistance values (i.e. 10 to 180 ohms) using Maretron’s DSM150, DSM200, or DSM250 display?

Jul 10, 2008 0 0 4430 0/5 (0 Vote)

Yes, it is possible to set the RAA100 to accept European standard resistive sensors using Maretron's DSM150, DSM200, or DSM250 display. Set the mode using Maretron's DSM150, DSM200, or DSM250 display in the following way. Enter menu mode, scroll to ... Read More

What information does the RAA100 provide?

Jul 10, 2008 0 0 4365 0/5 (0 Vote)

The RAA100 provides the the rudder angle. Read More

Results 21 - 30 of 32