Congratulations on your
purchase of the Maretron CKM12 12 Button Customizable Keypad.
Carling Technologies has proudly
designed and built your CKM12 to the highest standards for reliability and
accurate service.
The CKM12 is a sealed, IP69K
front rated, customizable keypad ready to
deliver years of dependable operation within the harsh demands of the marine
environment. The CKM12 features 12 keys and a rubberized coating over the
keypad. The CKM12 reduces installation time and the complexity and cost of
traditional wiring harnesses by utilizing NMEA 2000® CAN interface technology.
The CKM12 connects directly to an
NMEA 2000® network through the use of a CKM to NMEA
2000® Adapter Cable. Configure the CKM12 by using a Maretron USB100 or IPG100
tethering the NMEA2000® network to a PC running N2KAnalyzer. Control MPower and
other Maretron systems with the CKM12 through an NMEA 2000® Network. Using standard NMEA 2000® messaging, the CKM12 can
illuminate any of its 12 blue LED lights for status of circuit state.
The CKM12 is available in 2 standard
configurations. Custom configurations are available with a minimum order
quantity of 100 pieces.
Please carefully read and follow these instructions
for installation, configuration, and usage of the Maretron CKM12 module to
ensure optimal performance.
·
Key Detent Provides Tactile feel
when pressing
·
Configurable Operation and Appearance Aspect
- All Key Positions have Blue LED’s
- Horizontal or Vertical Mounting Options
- Screwless, Snap-In Mounting
- IP69 Rated (front) IP68 (rear) with Plug for Unused
Connector
- NMEA 2000 CAN Protocol
- LED Feedback of Controlled Circuit State
- Low Current Consumption (Max Current 100mA)
- NMEA 2000 LEN: 2
- Operating Voltage: 8 - 32 VDC
- Endurance Tested to Reach Minimum of 1,000,000 Operations
For Technical Specifications please refer to page 11
Key position will be reported
via the NMEA2000® Standard 127501 “Binary Status Report” CAN message. Each
button is considered a separate binary (on or off) switch and will be numbered
as follows:
Figure 1 - Key
Numbering
There is a total of twelve
blue LEDs, each configurable via CAN message to act as a function indicator. The
LEDs are located above the top row of keys and below the bottom row of keys. The
icons on each key are lit by an LED backlight located behind the icon. LEDs can
be tied to a channel of any device on the CAN network that reports the
NMEA2000® standard 127501 “Binary Status Report” message. When the associated channel
reports it is in the “on” state, the LED will be turned on and set to the
function indicator brightness level. When the associated channel reports it is
in the “off” state, the LED would be extinguished.
Figure 2 - Hardware
Description Front View
Figure 3 - Hardware
Description Top View
Figure 4 - Hardware
Description Back View
Figure 5 - CKM to
NMEA 2000® Adapter Cable (A3703)
The CKM12 can be
ordered as outlined in Table 1.
Custom Configurations
are available with a minimum order of 100 units.
Contact Marine.Sales@carlingtech.com for custom quotation.
Table 1 – Ordering
Options
|
PART NUMBER
|
DESCRIPTION
|
|
A3802-1
|
CKM12
Keypad (Circle on Buttons) with CKM to NMEA 2000® Adapter Cable .2m (A3703) (Horizontal
or Vertical Installation)
|
|
A3802-2
|
CKM12
Keypad (Number in Center of Circle on Buttons) with CKM to NMEA 2000® Adapter
Cable .2m (A3703) (Horizontal Installation)
|
|
A3703
|
CKM to
NMEA 2000® Adapter Cable - .2M
|
A3802-1
A3802-2
Installing the Maretron CKM12 involves the following
steps.
When unpacking the box containing the Maretron CKM12, you
should find the following items:
1 – CKM12 – 12 Button Keypad
1 – CKM12 User’s Manual on USB
flash drive
1 – CKM12 Panel
Installation Template
1 –
Warranty Registration Card
1 – A3703 CKM
to NMEA 2000® Adapter Cable
2 – 10-32 Nuts (Mounting Hardware)
If any of these items are missing or damaged, please
contact Maretron Technical Support
(please refer to page 13 for contact information).
Please consider the following when choosing a mounting
location.
- The
CKM12 is waterproof, so it can be installed in a damp or dry location.
- Consider
mounting depth (5” recommended clearance needed for proper cable bend
radius)
- The
CKM12 is temperature-rated to 85°C (185°F). Mount CKM12 away from engines
or engine rooms where the operating temperature exceeds the specified limit.
- After
mounting, ensure cable strain relief.
Locate the panel mounting template supplied with the CKM12.
After cutting panel mounting holes. Place the CKM12 into panel cutout. The CKM12
mounting studs will protrude to the backside of the panel hole. The use of
silicone sealant is acceptable to provide extra sealing protection of the CKM12
to the mounting panel. Thread supplied 10-32 nuts onto these threaded studs.
Tighten to 30 In. lbs. Do not use permanent adhesive to install unit. Certain
adhesives such as methacrylate will cause cracking of the plastic enclosure. The
use of permanent adhesive for installation will void warranty of CKM12 unit. For
reference to the needed panel cutout dimensions see Figure 6.
Figure 6 - Mounting
Panel Cutout Dimension
Connecting the CKM12 consists of plugging the unit to the
vessel’s NMEA 2000® network. The unit can be connected to NMEA 2000 network
directly to the 6 position Deutsch DT Series receptacle molded into the unit or
via use of the A3703 CKM to NMEA 2000® Adapter Cable.
Table 2 – 6 Position
Connector Pin Description
|
Connector
Pin No. (Location)
|
Description
|
|
1
|
NET_S (Batt. +)
|
|
2
|
NET_L (CAN_L)
|
|
3
|
NET_C (Batt. -)
|
|
4
|
Unused
|
|
5
|
NET_H (CAN_H)
|
|
6
|
Shield
|
The NMEA 2000® connector is the round five-pin male
connector found on the VMM to
NMEA 2000® Adapter Cable. This
connector is known as a DeviceNet micro connector. You connect the VMM6 to a
NMEA 2000® network using a Maretron NMEA 2000® cable (or compatible cable) by
connecting the female end of the cable to the male NMEA 2000 connector VMM to NMEA 2000® Adapter Cable. (note the key on
the male connector and keyway on the female connector). Be sure the cable is
connected securely and that the collar on the cable connector is tightened
firmly. Connect the other end of the cable by plugging into the 6 position
connector on the rear of the CKM12, applying pressure until the connector latch
clicks. The CKM12 is designed so that you can plug or unplug it from an NMEA
2000® network while the power to the network is connected or disconnected.
Please follow recommended practices for installing NMEA 2000® network products.
NMEA 2000 connections can be made using pre-assembled
leads or may be made using field attachable connectors and cables (See: Figure 7).
Figure
7 - NMEA 2000 Connectors
Please refer the Maretron website (www.maretron.com/products/cabling.php
) for relevant products.
The CKM12
transmits data over an NMEA 2000® network as it is shipped from the
factory. The default device instance is “Instance 50”. The default data
instance whose state is reflected by the LED’s on the CKM12 is “Instance 32”.
The unit will pair with Maretron CLMD12 and CLMD16 to toggle each unit’s first 12
ECB’s ON and OFF. If more than one CLMD12, CLMD16 or one of each unit is on the
same NMEA 2000® network the CKM12 unit will have to be configured. Depending on
desired switch control, default configuration may not work for your application
and custom configuration will be needed. The CKM12 is configured using Maretron
N2KAnalyzer® The following describe the configurable parameters of the CKM12.
Figure 8 – General
Tab Dialog Box
When connected to a NMEA 2000® network, this read-only
field will indicate the indicator bank instance value that will be transmitted
with the switch status in the 127501 Binary Status Report status message. To
change the value of this field, change the value of the CKM12 device instance,
as shown in Advanced Tab.
The CKM12 has 12 Keys, each with a separate indicator
output number referencing each key number as depicted in Figure 1 - Key
Numbering on page 2.
This Data Instance and Indicator
will be the instance information in which the VMM6 will be tethered to via PGN.
The LED for the corresponding switch will be lit or
flashing whenever the Indicator that corresponds to the selected Data
Instance is transmitting an On or fault state on the network.
The LED on the key will be dark otherwise.
Figure 9
– Advanced Tab Dialog Box
This tab contains the Device Instance setting; If
there are multiple instances of this device on a network each would be set to a
separate instance.
Regular maintenance is important
to ensure continued proper operation of the Maretron CKM12. Perform the
following tasks periodically:
• Clean the unit with a soft cloth and mild soapy water.
Do not use chemical cleaners as they may remove paint and markings or may
corrode the CLMD16 enclosure or seals. Do not use any astringent cleaners such
as acetone, MEK, Alcohol, Etc. These cleaners will deteriorate the CKM12 unit.
• Ensure that the unit is mounted securely and cannot be
moved relative to the mounting surface.
• Check the security of the cable connected to the NMEA
2000® connector and tighten if necessary.
If you notice
unexpected operation of the Maretron CKM12, follow the troubleshooting
procedures in this section to remedy simple problems. If these
steps do not solve your problem,
please contact Maretron Technical Support. Refer to page 13 for contact information.
Table 3 -
Troubleshooting Symptoms and Check Procedure
|
Symptom
|
Troubleshooting Procedure
|
|
CKM12 Module
Un-Responsive
|
• Check Connections to CKM to NMEA 2000®
Adapter Cable.
• Using a Maretron USB100 or Maretron IPG100, connect
to the NMEA 2000® network and ensure device is configured.
|
|
Any other problems
|
• Please refer to the CKM12 product page on the Maretron website for additional
troubleshooting suggestions.
|
As Carling is
constantly improving its products, all specifications are subject to change
without notice.
|
Parameter
|
Comment
|
|
NMEA 2000® Standard
|
Certified
|
|
CE Mark
|
Recreational Craft Directive 2014/35/EU
|
|
Description
|
PGN #
|
PGN Name
|
Default
Rate
|
|
Periodic Data PGNs
|
127501
|
Binary Status Report
|
1 time / 15 seconds and on
switch change
|
|
Response to Requested PGNs
|
126464
|
PGN List (Transmit and Receive)
|
N/A
|
|
126996
|
Product Information
|
N/A
|
|
126998
|
Configuration Information
|
N/A
|
|
065300
|
Proprietary
|
N/A
|
|
Protocol PGNs
|
059392
|
ISO Acknowledge
|
N/A
|
|
059904
|
ISO Request
|
N/A
|
|
060928
|
ISO Address Claim
|
N/A
|
|
065240
|
ISO Address Command
|
N/A
|
|
126208
|
NMEA
Request/Command/Acknowledge
|
N/A
|
|
126993
|
Heartbeat
|
1 time / 60 seconds
|
|
Parameter
|
Value
|
Comment
|
|
Operating
Voltage
|
8 – 32 VDC
|
|
|
Power Consumption
|
100 mA
|
NMEA 2000® Interface
|
|
Load Equivalence Number (LEN)
|
2
|
NMEA 2000® Spec.
(1LEN = 50 mA)
|
|
Communication
|
CAN 2.0b
|
NMEA 2000® Interface
|
|
Programming
|
Proprietary
|
Via Maretron USB100 or IPG100
|
|
Insulation Resistance
|
ISO 16750-2
|
500VDC with a
duration of 60s
|
|
Electrical Endurance
|
1,000,000 Operations
|
|
|
Parameter
|
Value
|
Comment
|
|
Size
|
6.49” x 2.3” x 1.28”
(164.84mm x 58.42mm x 32.51mm)
|
|
|
Weight
|
0.35 lb. (0.158 kg)
|
|
|
Material
|
Front Membrane – Silicone
Housing - Acetal, UV
stabilized
|
|
|
Illumination
|
12- Independent LEDs
|
Located under each button
|
|
Dimming
|
|
|
|
Connection
|
Deutsch DT-Series 6 pin
receptacle
|
|
|
Mounting
|
2-
10-32 Threaded Studs
(Rear Mounted)
|
|
|
Parameter
|
Value
|
|
Operating Temperature
|
-40°C to 85°C
|
|
Ingress Protection
|
IP69 (Front)
IP68 (Rear)
|
|
Storage Temperature
|
-40°C to 85°C
|
|
Ignition Protection
|
Ignition Protected
|
|
Parameter
|
Standard
|
Conditions
|
|
High Temperature Soak
|
EN 60068-2-2:2007
|
96hrs. @ 85°C
|
|
Low Temperature Soak
|
EN 60068-2-1:2007
|
96 hrs. @ -40°C
|
|
Temperature Cycling (Operating)
|
IEC 60068-2-14:2009
|
-40°C - 85°C (2 cycles of 8 hrs.)
|
|
Temperature Shock (Storage)
|
IEC 60068-2-14:2009
|
Tmin = -40°C, Tmax = 85°C
|
|
Simulated Solar Radiation
|
EN 60068-2-5:2010
(Procedure B)
|
10 days @ 40°C
|
|
Ignition Protection
|
ISO 8846
|
|
|
Humidity (Soak)
|
EN 60068-2-78:2002
|
RH = 93% +/-3%, Exposure
10 days
|
|
Humidity - Cyclic
|
EN 60068-2-30:2005
|
RH (> 90%), 6 cycles of
24hrs
|
|
Dust Ingress
|
IEC 60529:2001
|
Method EN60529 Section 13
Result IP6X
|
|
Water Ingress
|
DIN 40050-9:1993
IEC 60529:2001
|
Method as DIN 40050-9
Result IP69K
|
|
Mechanical Shock - Drop Test
|
EN 60068-2-31:1993
|
500mm free-fall, all faces
of 3 axes
|
|
Mechanical - Shock
|
60068-2-27:2009
|
500m/s2, pulse duration 11ms
|
|
Mechanical - Bump
|
60068-2-29:1993
|
400m/s2 6ms shock pulses, 3 axes
|
|
Vibration (General)
|
60068-2-6: 1996
|
Sine shaped sweep 5 Hz to
500 Hz Amplitude, 5g, (20 Cycles in each plane)
|
|
Vibration (Random)
|
EN 60068-2-64:1995
(Method 1)
|
Random excitation at 10,
150, 220, and 350 Hz breakpoint frequencies, 5 hours in each axis
|
|
Vibration (Resonant Search)
|
60068-2-6: 1996
|
frequency range 10 Hz – 2
kHz @ 5G (5 Minutes at each resonant point)
|
|
Chemical Resistance
|
ISO 16750-5 (Method 2)
|
Test method = B
|
|
Salt Spray(Corrosion Resistance)
|
EN 60068-2-52: 1996
|
Chamber Temperature = 35°C
(level 4 severity)
|
|
Component Test - Electrical Transients Immunity
|
ISO 11452-2:2004
|
100V/m, 20MHz to
2GHz
|
|
Component Test - Electrical Transients Emissions
|
ISO 13766:2006
Section 5
Annex D and Annex E
|
Distance of 1 m in the horizontal
and vertical polarization, 30 MHz to 1 GHz
|
|
Component Test - Electrical Transients Conducted
|
ISO
7637-2:2004
|
Method as per ISO
7637-2-Annex A2
|
|
Electrostatic Discharge (ESD)
|
ISO 10605
|
+/- 8 kV (Direct), +/- 15
kV (Air)
|
If you require technical support
for Maretron products, you can reach us in any of the following ways:
Telephone: 1-866-550-9100
Fax: 1-602-861-1777
E-mail: support@maretron.com
World Wide Web: http://www.maretron.com
Mail: Carling Technologies, Inc.
Attn: Maretron Technical
Support 120 Intracoastal Pointe Dr.
Jupiter, FL 33477 USA
Figure 10 - Technical
Support QR Code
Scan this QR code with your
smartphone for full technical information and a copy of this installation
manual.
Carling Technologies warrants the
Maretron® CLMD16 to be free from defects in materials and
workmanship for
two (2) years from the date of original
purchase. If within the applicable period any such products shall be proved to
Carling’s satisfaction to fail to meet the above limited warranty, such
products shall be repaired or replaced at Carling’s option. Purchaser's
exclusive remedy and Carling’s sole obligation hereunder, provided product is
returned pursuant to the return
requirements below, shall be limited
to the repair or replacement, at Carling’s option, of any product not meeting the
above limited warranty and which is returned to Carling; or if Carling is
unable to deliver a replacement that is free from
defects in materials or workmanship, Purchaser’s payment for such product
will be refunded. Carling assumes
no liability whatsoever for expenses of removing any defective product
or part or for installing the repaired product or part or a replacement
therefore or for any loss or damage to equipment in connection with which
Maretron® products or parts shall be used. With respect to
products not manufactured by Carling, Carling’s warranty
obligation shall in all respects
conform to and be limited
to the warranty actually extended to Carling by its supplier. The foregoing warranties shall not apply
with respect to products subjected
to negligence, misuse,
misapplication, accident, damages by circumstances beyond Carling’s control, to
improper installation, operation, maintenance, or storage, or to other than
normal use or service.
THE FOREGOING WARRANTIES ARE EXPRESSLY IN LIEU OF AND
EXCLUDES ALL OTHER EXPRESS OR IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND OF FITNESS FOR A PARTICULAR
PURPOSE.
Statements made by any person, including
representatives of Carling, which are inconsistent or in conflict with the
terms of this Limited Warranty, shall not be binding upon Carling unless
reduced to writing and approved by an officer of Carling.
IN NO CASE WILL CARLING
BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES,
DAMAGES FOR LOSS OF USE, LOSS OF ANTICIPATED PROFITS OR SAVINGS,
OR ANY OTHER LOSS INCURRED
BECAUSE OF INTERRUPTION OF SERVICE. IN NO EVENT SHALL CARLING’S
AGGREGATE LIABILITY EXCEED THE PURCHASE PRICE OF THE PRODUCT(S) INVOLVED.
CARLING SHALL NOT BE SUBJECT TO ANY OTHER OBLIGATIONS OR LIABILITIES, WHETHER
ARISING OUT OF BREACH OF CONTRACT OR WARRANTY, TORT (INCLUDING NEGLIGENCE), OR
OTHER THEORIES OF LAW WITH RESPECT TO PRODUCTS SOLD OR SERVICES RENDERED BY
CARLING, OR ANY UNDERTAKINGS, ACTS OR OMISSIONS RELATING THERETO.
Carling does not warrant that the functions contained
in any software programs or products will meet purchaser’s requirements or that
the operation of the software programs or products will be uninterrupted or
error free. Purchaser assumes responsibility for the selection of the software
programs or products to achieve the intended results, and for the installation, use and results
obtained from said programs or products. No specifications, samples, descriptions, or
illustrations provided Carling to Purchaser, whether directly, in trade literature,
brochures or other documentation shall be construed as warranties of
any kind, and any failure to conform with such specifications, samples, descriptions, or illustrations shall not constitute any breach of Carling’s
limited warranty.
To apply for warranty claims, contact Carling
Technologies or one of its Maretron dealers to describe the problem and
determine the appropriate course of action. If a return is necessary, place the
product in its original packaging together with proof of purchase and complete
a Return Merchandise Authorization (RMA) on the following web page:
https://www.maretron.com/rma_request.php
You
will be contacted by email with instructions on where to send the unit for
repair / evaluation. You are responsible for all shipping and insurance
charges. Carling will return the replaced or repaired product with all shipping
and handling prepaid except for requests requiring expedited shipping (i.e.,
overnight shipments). Failure to follow this warranty return procedure could
result in the product’s warranty becoming null and void.
Carling reserves the right to modify
or replace, at its sole discretion, without prior notification, the warranty
listed above. To obtain a copy of the then current warranty policy for Maretron® products, please go to the following
web page:
http://www.maretron.com/company/warranty.php
This appendix is
intended to relate specific characteristics of the CKM12 to how they are
communicated via NMEA 2000® messages in order to help ascertain
whether the messaging implemented by the CKM12 is compatible with other NMEA
2000®
products. It is not a complete description of the messages. If you
require detailed information on the messages, please obtain a copy of the NMEA
2000®
standard documents from the National Marine Electronics Association (www.nmea.org.
The CKM12 uses
this PGN to transmit the state of the 12 Keys.
Field 1: Indicator Bank Instance – This field identifies the particular indicator
bank to which this PGN applies. Please refer to Configuring
the CKM12
on page 8 for instructions on how to program the value of this field.
2: Indicator #1 – This field indicates the state of Key
#1.
The state will be one of the following values:
•
“OFF” – The button is not pressed
•
“ON” – The button is pressed
3 to 13: indicates
the state of the 12 keys, 2 to 12 respectively.
