Knowledge Base

Articles: Search Results

  1. Does N2KAnalyzer offer a software tool to perform quick fluid level calibrations for all of Maretron’s tank monitoring products? Yes, N2Kanalyzer offers two types of tank calibrations: Manual Table and Step Fill. Both configuration features can be used to calibrate the correct tank volume for your Maretron tank monitoring product.Used in in conjunction with any of Maretron... Read More
  2. Does Maretron offer a DSM410 Gimble mount? Does Maretron offer a DSM410 Gimbal mount?No, Maretron does not sell a DSM410 gimble mount.However, we do provide a 3D printer "STL" file (located in the attachment section below) that allows a 3D printer program to make the hardware on a 3D printer ... Read More
  3. Does Maretron offer a Quick Setup guide for the SIM100 using N2KAnalyzer? Maretron's Switch Indicator Module monitors dry contacts. Once you have selected the dry contact device, connect the two leads from the device to one of six SIM100 channels.Each channel has two terminals; for example, Channel #0 uses terminals 1... Read More
  4. I see N2KView offers a component for "Indicator Status"; what products can I use to show Indicator Status? An Indicator Status component uses the NMEA 2000 message called "Binary Switch Bank Status" to show three condition states:OnOffErrorA RIM100, SIM100, and DCR100 all transmit the necessary message for the N2KView component to work.You can create seve... Read More
  5. Does Maretron offer quick setup instructions for the FFM100 in a single diesel engine application? The prerequisite for using this guide requires the use of a Windows PC and Maretron's N2KAnalyzer program installed. The hardware required for Maretron device configuration is the USB100 or IPG100 Gateway connected to a powered N2K network with ... Read More
  6. How do I make a custom NMEA 2000 cordset cable? Does Maretron offer a field attachable connector? Maretron offers several accessories that allow you to make a custom NMEA 2000 cable.It may be necessary to make a custom cable for the following reasons:Cable runs longer than 10m in lengthRouting raw cables micro/mid through bulkheads, wire trays, a... Read More
  7. The DCR100 will not allow me to switch on/off a relay channel. Why? The DCR100 has a DC current calibration option. If you have connected a DC load to a channel of the DCR100 and have not performed the "Current Sensor Zero Offset Calibration", this may affect the command of this channel especially if the DCR100 detec... Read More
  8. Does Maretron offer a quick setup guide for the DCM100? Configuring the DCM100 using the DSM150 or DSM250 display.Perform a current sensor zero offset with the current sensor attached to the DCM100.Step two: Scroll to DC Type and input the DC battery configuration:Configuring the DCM100 using the N2KAnaly... Read More
  9. In addition to switching On and Off DC loads, can I use the DCR100 to monitor current flow to the loads? Yes, you can use the DCR100 to monitor DC current flow to loads using one of Maretron's display products (e.g., N2KView, DSM150, or DSM250). Each of the six channels within the DCR100 reports how much current is flowing to the load, which is use... Read More
  10. Can I turn On and Off loads connected to the DCR100 using the DSM150 or DSM250? Yes, you can turn On and Off loads connected to the DCR100 using the DSM150 or DSM250. To do so, you should understand a few things about the DSM150 or DSM250 and its favorite screens. First, you need to understand how to setup a favorite screen with... Read More
Displaying 1 to 10 out of 167 records First Page Previous Page Page of 17 Next Page Last Page

Icon Search Advanced Search
Show
That Contains
But Not
In
Search for
Search in
Sort by
Also search in Attachments
 
Subscribe to knowledgebase
Get notified when new articles are added to the knowledgebase.
 
Copyright© 2019 Carling Technologies. All rights reserved. Visit Carling Technologies, a partner company.