What firmware changes have taken place on the Maretron SSC200?

What firmware changes have taken place on the Maretron SSC200 Compass? 

Update your device today using the N2KAnalyzer software tool.

SSC200 Firmware Versions

5.0.4.1(2013-07)

  • Correct Gyro Offset Table Issue (2463)
  • Increase the acceptable error range of Gyro Temperature Offset to 15 degree C (2666)

 

 

5.0.3(2010-06)

  • Re-Enabled "store baud command" for 0183 configurations.
  • Hardware improvements 

 

3.0.2 (2010-05)

  • Corrected issue when 0° would display when heading was truly 180°

3.0.1 (2010-04-23)

  • Increased maximum heading (PGN 127250) transmission rate from 10Hz (100ms) to 40Hz (25ms)

 

2.0.11 (2009-03-04)

  • Added support for labeling so that the device can easily be identified with a user-programmable string

 

2.0.10 (2008-03-03)

  • Fixed problem where the device tried to transmit a PGN before it had acquired a node address

 

2.0.9 (2007-08-30)

  • Corrected a problem with programming of installation offset

 

1.10.2, 2.0.2 (2006-01-31)

  • Support deviation for calibration ignoring accelerometers (“No Acc”) for calibration on large vessels

 

1.10.1, 2.0.1 (2005-10-03)

  • Send sequence of headings 0 degrees, 90 degrees, 180 degrees, 270 degrees for one second each after successful magnetic deviation calibration

 

1.10.0, 2.0.0 (2005-09-09)

  • Added support for OEM product versions
  • Updated supported NMEA 2000 protocol version to 1.2
  • Added support for inverted and backwards installation

 

1.9.2 (2005-07-14)

  • No user-visible changes (manufacturing improvements)

 

1.9.1          (2005-07-07)

  • No user-visible changes (manufacturing improvements)

 

1.9   (2005-05-13)

  • Added ability to configure rate of transmission of NMEA 2000 messages
  • Added support for 40Hz operation on NMEA 0183
  • Added ability to report status of magnetic deviation
  • Added ability to perform rate of turn zero offset calibration
  • Correct the automatic selection of magnetic variation sources when multiple are available

 

1.8   (2005-03-11)

  • Added the capability to have NMEA 0183 sentences enabled or disabled from a DSM200 or DSM250 display
  • Added ability to automatically receive magnetic variation from either NMEA 2000 or NMEA 0183 interfaces
  • Fixed a heading error when heading changes between 180 and 179 degrees
  • Added the capability to be programmed with a manual magnetic variation entry for use when no variation data is available from other devices
  • Changed to always use the best quality source of magnetic variation when multiple sources are available
  • Changed to not require a checksum on received NMEA 0183 sentences
  • Updated supported NMEA 2000 protocol version to 1.111
  • Changed averaging periods on rate of turn and heading

 1.7   (2005-04-02)

  • Modified NMEA 0183 sentences HDG,HDM,HDT to add leading zero to all heading related fields so that they display in the "xxx.x" format
  • Made the NMEA 0183 sentences VTG and RMC backward compatible to NMEA0183 2.01 (ignore mode indication field if this field does not exist)
  • Made the NMEA 0183 device identifier programmable

 1.6 (2005-01-21)

  • Initial public release
Posted - Mon, May 16, 2011 2:05 PM. This article has been viewed 4542 times.
Online URL: https://www.maretron.com/support/knowledgebase/phpkbv7/article.php?id=423