Device Configuration Using DSM250 - Maretron Knowledge Base

The prerequisite for using this guide requires the use of a Windows PC and Maretron's N2KAnalyzer program installed. The hardware required for Maretron device configuration is the USB100 or IPG100 Gateway connected to a powered N2K network with ... Read More

How do I configure an EMS100 that is connected to a Yanmar engine?

Viewed 7049 times since Tue, Sep 1, 2009

NOTE: The EMS100 has been discontinued and is no longer offered for sale.To configure the EMS100 using the DSM250, start from the favorite screen mode and press the enter key or the far right hand button, scroll to configuration and press enter, scro... Read More

How do I set up the EMS100 for my Yanmar engine?

Viewed 6277 times since Tue, May 10, 2011

In order to setup an EMS100 several things must be known.What senders have been installed on the engine?What type of engine gauge panel is installed with the engine?Where is the factory interface available for the EMS100 engine harness to tee into?On... Read More

How do I perform a cold start on the GPS100 using the DSM250 Display?

Viewed 6098 times since Tue, May 10, 2011

To perform a cold start on the GPS100 using the Maretron DSM150, DSM200, or DSM250 display. Enter menu mode, scroll to "Configuration..." and press enter. Scroll to "Device Configuration..." and press enter. Scroll to the GPS100 and press enter. Scr... Read More

What are the basic configurable parameters for the TLM100 and how do I configure them using a DSM250?

Viewed 4538 times since Wed, Oct 7, 2009

What are the basic configuration items of the TLM100 and how do I perform them using a DSM250? The TLM100 comes from the factory pre--configured for a 40 inch depth, rectangular fuel tank. By default, the TLM100 is configured to transmit information ... Read More

What is the procedure for testing the ALM100 Annunciator?

Viewed 4364 times since Thu, Jan 8, 2015

The procedure for testing an ALM100 can be performed using the following Maretron User Interface products:DSM150/DSM250:Go to Main Menu-->Scroll to Configuration-->Select "Device Configuration"-->Select the ALM00 you wish to test-->Scroll to "Test An... Read More

What are the basic configurable parameters of the TLM150 and how do I configure them using a DSM250?

Viewed 3650 times since Mon, Oct 5, 2009

What are the basic configuration items of the TLM150 and how do I perform them using a DSM250?The TLM150 comes from the factory preconfigured for a 24 inch depth, rectangular fuel tank. By default, the TLM150 is configured to transmit information ove... Read More

How do I set a "Device Instance" for a Maretron sensor using the DSM250?

Viewed 3561 times since Tue, Sep 1, 2009

To set a "Device Instance" for a Maretron sensor using the DSM250, simply press the enter key (far right hand button) to view the "Menu Mode", scroll to "Configuration", hit enter, select "Device Configuration", hit enter, scroll to the desired devic... Read More

What are the basic configurable parameters of the TLM200 and how do I configure them using a DSM250?

Viewed 3189 times since Mon, Oct 5, 2009

What are the basic configuration items of the TLM200 and how do I perform them using a DSM250?The TLM200 comes from the factory preconfigured for a 104 inch depth, rectangular fuel tank. By default, the TLM200 is configured to transmit information ov... Read More

Does Maretron offer a Quick Setup guide for the SIM100 using N2KAnalyzer?

Viewed 3182 times since Tue, May 5, 2015

Maretron's Switch Indicator Module monitors dry contacts. Once you have selected the dry contact device, connect the two leads from the device to one of six SIM100 channels.Each channel has two terminals; for example, Channel #0 uses terminals 1... Read More

Can I use the DSM150 or DSM250 to configure a DCR100?

Viewed 3118 times since Tue, May 10, 2011

Yes, you can use a DSM150 or DSM250 to configure a DCR100. Please watch the following video to see how it's done. Read More

What configuration options are available for the TMP100?

Viewed 2842 times since Tue, Oct 25, 2016

Use the N2KAnalyzer software program or a Maretron DSM150, or Maretron DSM250 to perform Maretron Device level configuration. This article will show methods for configuring the TMP100 Using Maretron's N2KAnalyzer software tool. Pre-requisits:PC... Read More

How do I configure a channel on the SIM100 using Maretron’s DSM250 Display?

Viewed 2445 times since Tue, Sep 1, 2009

You configure a channel on the SIM100 in the following way. Enter menu mode, scroll to "Configuration?" and press enter. Scroll to "Device Configuration?" and press enter. Scroll to the row containing SIM100 and press enter. Select instance pr... Read More

Subscribe to knowledgebase
Get notified when new articles are added to the knowledgebase.