|
How do I perform J2K100 quick setup using the N2KAnalyzer program?
Viewed 28983 times since Wed, Oct 10, 2012
Refer to this article for help on setting up your first J2K100 especially when connected to the following engine manufacturers J1939 networks:Caterpillar, John Deere, Cummins, Steyr, ECU Delphi Mefi 4-6, Crusader, MAN, Detroit Diesel, Volvo-Penta (EV... Read More
Is there a list of NMEA 2000 messages (a message is identified by a Parameter Group Number, or PGN)?
Viewed 20902 times since Wed, Oct 10, 2012
Yes, the National Marine Electronics Association (NMEA) publishes a list of PGNs, which can be found via this link:http://www.nmea.org/content/nmea_standards/messages_pgns.asp Read More
What software changes have taken place with N2KAnalyzer?
Viewed 5987 times since Wed, Apr 16, 2014
What changes have taken place with the N2KAnalyzer?Current Version Available: N2KAnalyzer 2.4.22 Updates for VDR100, FPM100 includes features for N2K diagnostics, and much more. **USERS RUNNING N2KANALYZER VERSION 2.1.14, YOU WILL NEED TO MANUALLY... Read More
I see the Tank Level Monitor products have a specification called "deadband"; what is this and how does it affect tank measurements?
Viewed 5459 times since Fri, May 8, 2015
en discussing the TLM100, TLM150, and TLM200 ultrasonic tank level sensors, the term "deadband" is a term used when describing an operating range where a signal start and signal end cannot be measured.For an ultrasonic sensor application, deadband is... Read More
Does N2KAnalyzer offer a software tool to perform quick fluid level calibrations for all of Maretron’s tank monitoring products?
Viewed 4705 times since Thu, Nov 27, 2014
Yes, N2Kanalyzer offers two types of tank calibrations: Manual Table and Step Fill. Both configuration features can be used to calibrate the correct tank volume for your Maretron tank monitoring product.Used in in conjunction with any of Maretron... Read More
I have configured my DSM410 or DSM250; how do I perform a backup?
Viewed 4662 times since Tue, Feb 26, 2013
Now that you have configured your DSM250 or DSM410 just the way you want it. Once complete you can backup all your work using the following method: You must have several items installed on the NMEA 2000 network and your PC to begin:USB100 or IPG100D... Read More
Some helpful information to installing your first or the next Maretron N2KNetwork.
Viewed 4496 times since Thu, Feb 3, 2011
This article provides a summary of steps and methods you should use to ensure your installation of a Maretron system goes smoothly. The process of installing an NMEA 2000 network, big or small, can be overwhelming. Following are methods that are curr... Read More
Can Maretron’s DSM150 or DSM250 display or N2KAnalyzer configure certain Airmar transducers?
Viewed 4178 times since Thu, Mar 31, 2011
Yes, Maretron's multi-function color displays (DSM150 and DSM250) or Maretron's N2KAnalyzer configuration tool (used in conjunction with the USB100 or IPG100 gateway) can be used to configure certain Airmar transducers. Please see the attac... Read More
What is an N2KAnalyzer "boat file"?
Viewed 4121 times since Fri, Jun 26, 2009
N2KAnalyzer allows you to save information about a particular network for a given boat or vessel into what is called a "boat file". You can read the boat file back into N2KAnalyzer at a later time or you can even send the boat file to Maretron's... Read More
How do I save and load a configuration file for a TLM100, TLM150, or TLM200 using N2KAnalyzer?
Viewed 3827 times since Thu, Aug 25, 2011
N2KAnalyzer has a feature that allows for the user to load a saved configuration table onto a TLM100,TLM150, or TLM200 on the NMEA 2000 network. To load a configuration file, use the following process:Start the N2KAnalyzer program.Select a gateway to... Read More
How do I a create a vessel’s NMEA 2000 network file (boat file)?
Viewed 3646 times since Fri, Jun 26, 2009
You create, or save, a boat file through the file menu within N2KAnalyzer. First, left click on the "File" menu item found near the top left hand side of the N2KAnalyzer window. Next, left click on the "Save As..." menu item. A file browser window w... Read More
What is the procedure for testing the ALM100 Annunciator?
Viewed 3271 times since Thu, Jan 8, 2015
The procedure for testing an ALM100 can be performed using the following Maretron User Interface products:DSM150/DSM250:Go to Main Menu-->Scroll to Configuration-->Select "Device Configuration"-->Select the ALM00 you wish to test-->Scroll to "Test An... Read More
Using N2KAnalyzer, how do I recover a Maretron device?
Viewed 3179 times since Thu, Dec 22, 2011
Occasionally, a device can be in "boot mode" (represented in N2KAnalyzer by an orange highlight of the device's entry in the device list). This can happen due to a software update which fails due to network problems.A Maretron device that is not... Read More
How do I read a previously saved boat file back into N2KAnalyzer?
Viewed 3082 times since Thu, Jan 8, 2009
You read a previously saved boat file back into N2KAnalyzer by selecting the "File" menu and clicking on the "Open..." menu item. You can only read a boat file back into N2KAnalyzer if N2KAnalyzer is disconnected from an NMEA 2000 network (connectio... Read More
How do I perform a TLM100 quick setup for a square tank using the N2KAnalyzer program?
Viewed 2892 times since Fri, May 8, 2015
Quick setup guide for a TLM100. The following article was written assuming you(reader) are familiar with Maretron configuration tools and products. This article is intended for advanced users and NMEA certified Technicians who require quick reference... Read More
When I try to run N2KAnalyzer, I receive an error message asking for XMLLITE.DLL.
Viewed 2718 times since Wed, Jan 6, 2010
XMLLITE.dll is a file used in performance XML based applications. If the file has been damaged or removed from your system, it can be reinstalled in the following way: download and install XMLLITE.dll using the following link http://www.microsoft.c... Read More
What configuration options are available for the FPM100?
Viewed 2603 times since Thu, Oct 27, 2016
You can use the N2KAnalyzer software program or a Maretron DSM150, or Maretron DSM250 to perform the configuration. This article will show methods for configuring the FPM100 Using Maretron's N2KAnalyzer software tool. Pre-requisits:PC with N2KAn... Read More
What configuration options are available for the TMP100?
Viewed 2145 times since Tue, Oct 25, 2016
Use the N2KAnalyzer software program or a Maretron DSM150, or Maretron DSM250 to perform Maretron Device level configuration. This article will show methods for configuring the TMP100 Using Maretron's N2KAnalyzer software tool. Pre-requisits:PC... Read More
Does Maretron offer a Quick Setup guide for the SIM100 using N2KAnalyzer?
Viewed 1995 times since Tue, May 5, 2015
Maretron's Switch Indicator Module monitors dry contacts. Once you have selected the dry contact device, connect the two leads from the device to one of six SIM100 channels.Each channel has two terminals; for example, Channel #0 uses terminals 1... Read More
I have an AT&T SIM card inserted in my SMS100, how do I perform a test message for my cell account?
Viewed 1778 times since Fri, Jan 26, 2018
If you are expiriencing dificulty receiving a status message from your SMS100, perform the next steps locally using Maretron configuration tools like the N2KAnalyzer or a DSM product. Messaging-SMS Instructions:1. Unplug the SMS100 from the NMEA2000 ... Read More
Does Maretron offer quick setup instructions for the FFM100 in a dual diesel engine application?
Viewed 1499 times since Mon, Jun 24, 2019
The prerequisite for using this guide requires the use of a Windows PC and Maretron's N2KAnalyzer program installed. The hardware required for Maretron device configuration is the USB100 or IPG100 Gateway connected to a powered N2K network with ... Read More
Does Maretron offer quick setup instructions for the FFM100 in a dual gasoline engine application?
Viewed 1498 times since Thu, Jun 27, 2019
The prerequisite for using this guide requires the use of a Windows PC and Maretron's N2KAnalyzer program installed. The hardware required for Maretron device configuration is the USB100 or IPG100 Gateway connected to a powered N2K network with ... Read More
What configuration options are available for the DCM100?
Viewed 1491 times since Fri, Oct 28, 2016
Use the N2KAnalyzer software program or a Maretron DSM150, or Maretron DSM250 to perform Maretron Device level configuration. This article will show methods for configuring the DCM100 Using Maretron's N2KAnalyzer software tool. Pre-requisits:PC ... Read More
I see that the DCR100 has a configuration feature called Operating Mode, What does this mean?
Viewed 1328 times since Thu, Mar 23, 2017
DCR100 channels have two possible operating modes: “Normal”, in which the DCR100 channel responds to standard NMEA 2000 switching commands, and “Annunciator”, in which the channel may be connected to a power source for a sounder or a light to be acti... Read More
Can Maretron monitor a kerosene tank?
Viewed 432 times since Mon, Jan 20, 2020
Yes! Using the Maretron FPM100 paired with either our submersible (Part # PTS-0-xPSI-01) or external (Part # PT-0-xPSI-01) pressure transducers will be able to monitor this type of fuel successfully.Kerosene has a density level of 0.81 g/cm3 or 810 k... Read More
|