Knowledge Base
Home » Categories » Multiple Categories

What information is available from the J1939 to NMEA 2000 Bridge (J2K100) and can be viewed on Maretron’s displays?
Article Number: 586 | Rating: Unrated | Last Updated: Thu, Jul 30, 2015 10:58 PM

 The J2K100 is capable of transmitting the following information:

  • PGN 65030
    • AC Generator Current
    • AC Generator Frequency
    • AC Generator Voltage
  • Engine parameters 127488, 127489
    • Tachometer
    • Engine Hours
    • Coolant Pressure
    • Coolant Water Temperature
    • Engine Oil Pressure
    • Engine Oil Temperature
    • Boost Pressure
    • Fuel Rate Monitoring
    • Charging Voltage
    • Percent Engine Load
    • Percent Engine Torque
    • Rated Engine Speed
    • VIN
    • Software ID
    • Transmission Gear
    • Transmission Oil Pressure
    • Transmission Oil Temperature
  • Air conditioner proprietary PGN
    • Status
    • Control
  • Icemaker proprietary PGN
    • ON/OFF
    • Display Status
Posted - Mon, Jun 24, 2013 4:51 PM. This article has been viewed 3685 times.
Filed Under: DSM150 (Discontinued), DSM250 (Discontinued), DSM410, DSM800(Discontinued), J2K100, MBB100(Discontinued), TSM1330(Discontinued), TSM800(Discontinued)
Attachments Attachments
There are no attachments for this article.
Related Articles RSS Feed
How do I configure a channel on the TMP100 using Maretron’s DSM250?
Viewed 3424 times since Fri, Jun 11, 2010
How do I set the J2K100 configuration setting called "NMEA 2000 Transmission Instance:" using Maretron’s DSM150 or DSM250 display?
Viewed 4051 times since Thu, Jan 14, 2010
How do I know if the GPS100 is locked on and producing a position fix using Maretron’s DSM150, DSM200, or DSM250 display?
Viewed 3594 times since Tue, Jun 17, 2008
I see that Maretron’s DSM150, DSM200 and DSM250 displays have a WSO100 configuration setting called "Installation Offset Calibration..."; what is this?
Viewed 4458 times since Mon, Jul 21, 2008
How do I set the RAA100 configuration setting called "Gauge Resistance, - to sender" using Maretron’s DSM150, DSM200, or DSM250 display?
Viewed 3286 times since Thu, Jul 10, 2008
How do I set the TLA100 configuration setting called "Gauge Resistance, + to sender:" using Maretron’s DSM150, DSM200, or DSM250 display?
Viewed 3812 times since Mon, Jun 25, 2012
How do I make the SSC200 agree with other compasses on the vessel, or, in other words, how do I align the SSC200 with the boat?
Viewed 3055 times since Mon, Jun 25, 2012
How do I set the TLA100 configuration setting called "Gauge Resistance, - to sender" using Maretron’s DSM150, DSM200, or DSM250 display?
Viewed 3737 times since Fri, Jun 20, 2008
How is J1939 different from NMEA 2000?
Viewed 17256 times since Thu, Jan 14, 2010
How do I set the TLA100 tank number or instance using Maretron’s DSM150, DSM200, or DSM250 display?
Viewed 3439 times since Fri, Jun 20, 2008
  • Icon SubscriberSubscribe to Article
  • Icon PrinterPrint Article
  • Icon EmailEmail Article to Friend
  • Icon PDFExport to PDF
  • Icon MS-WordExport to MS Word
0 (0)
Article Rating (0 Votes)
Rate this article
Subscribe to knowledgebase
Get notified when new articles are added to the knowledgebase.
 
Copyright© 2019 Carling Technologies. All rights reserved. Visit Carling Technologies, a partner company.