Knowledge Base
Home » Categories » Multiple Categories

What firmware changes have taken place on the Maretron TLA100?

2.0.2.3 (2016-08-29):

  • Correct fluid source transmitted in Channel PGN (3959)
  • Corrected a problem where the device could lose its instance information after a power cycle (3964,
    3965, 3966, 3967)

 

2.0.1.5 (2015-10)

  • Initial Release to support Hardware Version 2

 

1.2.2.1     (2014-10-30)

  •  Added support for realtime display of resistance readings during calibration
  •  Corrected a problem where updating from an earlier software version could make the TLA100 stop working

 

1.6.15      (2009-08-10)

  • Added capability to have the resistance/level table configured by N2KAnalyzer

 

1.6.14 (2009-03-20)

  • Fixed a problem with custom calibration introduced in version 1.6.13

 

1.6.13 (2009-02-03)

  • Added support for labeling so that the device can easily be identified with a user-programmable string

 

1.6.12 (2008-08-22)

  • Fixed problem preventing custom calibration with Type 2 gauge from working

 

1.6.11 (2008-03-18)

  • Made improvements to device responsiveness to NMEA 2000 messages

 

1.6.10 (2008-03-14)

  • Implemented handling for Type 2 (Faria current-controlled) gauges

 

1.6.9 (2008-03-10)

  • Made improvements to device responsiveness to NMEA 2000 messages

 

1.6.6 (2007-10-11)

  • No user-visible changes (manufacturing improvements)

 

1.6.5 (2007-09-28)

  • Made improvements to device responsiveness to NMEA 2000 messages

 

1.6.3 (2006-06-29)

  • Modifications for NMEA 2000 certification

 

1.6 (2006-05-15)

  •  Initial public release

 

Attachments Attachments
There are no attachments for this article.
Related Articles RSS Feed
Can I set the TLA100 to accept the European standard for resistance values (i.e. 10 to 180 ohms) using Maretron’s DSM150, DSM200, or DSM250 display?
Viewed 1957 times since Thu, Jun 19, 2008
Why doesn’t my tank display doesn’t read empty when the tank is empty?
Viewed 1834 times since Sun, Jun 22, 2008
I see that Maretron’s DSM150, DSM200, and DSM250 displays have a TLA100 configuration setting called "NMEA 2000 PGN Enable/Disable..."; what is this?
Viewed 1841 times since Fri, Jun 20, 2008
How do I set the TLA100 tank capacity using Maretron’s DSM150, DSM200, or DSM250 display?
Viewed 2566 times since Mon, Jun 25, 2012
I see that Maretron’s DSM150, DSM200, and DSM250 displays have a TLA100 configuration setting called "Tank Capacity:"; what is this?
Viewed 2150 times since Thu, Jun 19, 2008
How long is the gray cable that is attached to the TLA100?
Viewed 2289 times since Tue, Jul 8, 2008
How do I set the TLA100 configuration setting called "Gauge Resistance, - to sender" using Maretron’s DSM150, DSM200, or DSM250 display?
Viewed 2286 times since Fri, Jun 20, 2008
What messages (or PGNs) does the TLA100 transmit?
Viewed 2249 times since Thu, Jun 19, 2008
If the TLA100 is connected and configured to operate in the "NMEA 2000" mode (i.e., without an analog gauge), how do I connect the wires to the resistive sensor?
Viewed 1525 times since Fri, Jun 20, 2008
I see that Maretron’s DSM150, DSM200, and DSM250 displays have a TLA100 configuration setting called "Operating Mode:"; what is this?
Viewed 2059 times since Thu, Jun 19, 2008
Subscribe to knowledgebase
Get notified when new articles are added to the knowledgebase.