Knowledge Base
Home » Categories » Multiple Categories

What firmware changes have taken place on the Maretron RAA100?

2.0.2.3 2016-08-29):

  • Corrected a problem where the device could lose its instance information after a power cycle (3968)

 

2.0.1.5  (2015-10)

- Initial Release to support Hardware Version 2

1.4.10 (2009-08-12)

- Corrected a problem with Maretron Label support where the device would not always accept a new label

 

1.4.9 (2009-02-03)

- Added support for labeling so that the device can easily be identified with a user-programmable string.

 

1.4.8 (2008-03-18)

- Fixed error in CAN filter implementation resulting in non-responsiveness

- Fixed a problem that prevented configuration from working when the configuring device had a node address greater than 127 (0x7F)

 

1.4.7 (2008-03-10)

- Made improvements to device responsiveness to NMEA 2000 messages

 

1.4.6 (2008-02-29)

- Made improvements to device responsiveness to NMEA 2000 messages

 

1.4.5 (2008-01-21)

- Made improvements to device responsiveness to NMEA 2000 messages

 

1.4.4 (2007-09-28)

- No user-visible changes

 

1.4.3 (2007-09-28)

- Corrected issue in CAN driver that caused RAA100 not to respond to product selection sometimes.

 

1.4.2 (2007-03-29)

- Corrected problems with custom calibration

 

1.4.1 (2006-05-24)

- Fixed an issue with NMEA 2000 certification

 

1.4 (2006-05-17)

- Fixed a problem causing occasional loss of received messages

 

1.2 (2006-03-21)

- Initial public release

Attachments Attachments
There are no attachments for this article.
Related Articles RSS Feed
I know that the RAA100 uses resistive rudder angle sensors; who manufactures resistive sensors?
Viewed 2285 times since Wed, Jun 6, 2012
Can I custom calibrate the RAA100 for non-standard resistance sensors or can I do custom calibration for hard over points other than 60 degrees?
Viewed 2730 times since Thu, Jul 10, 2008
How do I set the RAA100 configuration setting called "Gauge Resistance, + to sender" using Maretron’s DSM150, DSM200, or DSM250 display?
Viewed 3218 times since Fri, Jul 11, 2008
Is it possible to turn on or off RAA100 transmitted messages (or PGNs)?
Viewed 2973 times since Fri, Jul 11, 2008
If the RAA100 is connected and configured to operate in the "NMEA 2000" mode (i.e., without an analog gauge), how do I connect the wires to the resistive sensor?
Viewed 2356 times since Thu, Jul 10, 2008
What messages (or PGNs) does the RAA100 transmit?
Viewed 3078 times since Fri, Jul 11, 2008
What is the RAA100 configuration setting "Gauge Resistance, + to sender" and "Gauge Resistance, - to sender"?
Viewed 2752 times since Thu, Jul 10, 2008
Why I can’t find a RAA100 rudder angle for display on Maretron’s DSM150, DSM200, or DSM250?
Viewed 3812 times since Fri, Jul 11, 2008
What type of rudder senders does the RAA100 work with?
Viewed 1467 times since Thu, Jul 10, 2008
Can I set the RAA100 to accept the American standard for resistance values (i.e. 240 to 33 ohms) using Maretron’s DSM150, DSM200, or DSM250 display?
Viewed 3096 times since Fri, Jul 11, 2008
Subscribe to knowledgebase
Get notified when new articles are added to the knowledgebase.