Privacy Policy  |  Contact Us
Maretron Support Knowledge Base

Knowledgebase Home | Glossary | Favorites | Contact Knowledgebase Home | Glossary | Favorites | Contact
Search the Knowledgebase Browse by Category

[Advanced Search]
Advanced Search
* Query:
  Categories:
  Rated:
  Custom Fields:
Search Results for "yamaha adapter cable"
There were 29 articles found for your query: (Page 1 of 2)     «« |  Prev | 1 | 2 | Next | »»
  1. How do I install a WSO100?How do I install a WSO100?
    ... detachable pole mount on the mounting pole without the WSO100 attached. Next, attach the NMEA 2000 cable and/or inline terminator to the WSO100. Finally, attach the WSO100 to the pole mount with the ...

  2. Using the N2KAnalyzer how do I recover a device?Using the N2KAnalyzer how do I recover a device?
    The N2KAnalyzer software can restore a devices software using the following method: Select the affected device(represented by a row with light gray serial number shown), right-click ...

  3. What are the Voltage specifications for each Maretron device?What are the Voltage specifications for each Maretron device?
    Maretron Model Device Description NMEA2000 Operating Voltage Engine/Battery Interface SSC200 NMEA 2000 Solid State Compass HW 1.0 9 t...

  4. What is a TLA100?What is a TLA100?
    The TLA100 is a tank level adapter that converts an analog resitive tank sender into digital information, which is then broadcast over the NMEA 2000 where any NMEA 2000 compatible display can show the...

  5. How long is the gray cable that is attached to the TLA100?How long is the gray cable that is attached to the TLA100?
    The gray cable used to connect the TLA100 to the resitive tank sensor is aproximatelly 15 feet (4.57 meter) in length.

  6. How is the GPS100 mounted?How is the GPS100 mounted?
    ...screw or unscrew the GPS100 and pole mount off of the mounting pole as this will twist the attached cable and possibly damage the GPS100 connector.

  7. How long is the cord that is attached to the DST100?How long is the cord that is attached to the DST100?
    The NMEA 2000 cable attached to the DST100 is approximately 2 meters long (6.5 feet).

  8. What firmware changes have taken place on the Maretron DSM250?What firmware changes have taken place on the Maretron DSM250?
    - DSM250 firmware versions - 1.4.14.4(2012-04-06) - Added support for configuring FFM100 to use single-phase sensors (typically used for non-fuel fluid flow applications) - Improved dis...

  9. I have an Onan generator with a power rating between 4-32kW, what Maretron adapter cable should I order to connect the generator to the J2K100?I have an Onan generator with a power rating between 4-32kW, what Maretron adapter cable should I order to connect the generator to the J2K100?
    The Maretron adapter cable MCF-2M-D12 (J2K100 adapter Micro female to Deutsche 12 Pin 2 Meter Cords...

  10. I have an Onan generator with a power rating between 40-99kW, what Maretron adapter cable should I order to connect the generator to the J2K100?I have an Onan generator with a power rating between 40-99kW, what Maretron adapter cable should I order to connect the generator to the J2K100?
    You should order the Maretron adapter cable MCF-2M-D4 (J2K100 adapter Micro female to Deutsche 4 Pi...

  11. Does Maretron have a interface cable for Caterpillar engine networks to the J2K100 device?Does Maretron have a interface cable for Caterpillar engine networks to the J2K100 device?
    The MCF-2M-D12CAT cable is used to interface a J2K100 to a CAT marine power display. It is recommended that the MCF-2M-D12CAT cable should connect to one of two ports on the CAT display. The ideal con...

  12. How do I check the health of my N2K cabling before powering my network?How do I check the health of my N2K cabling before powering my network?
    ...ld measure 0 (open)ohms between pins 4 (White wire) and any of the four conductors on the network cable. If you measure any resistance between pins 4 and other conductors, you have a short somewher...

  13. Does Maretron make a waterproof USB cable for connecting the USB100 to a computer?Does Maretron make a waterproof USB cable for connecting the USB100 to a computer?
    No, Maretron does not make a waterproof USB cable for connection between the USB100 and a computer. However, a waterproof cable can be built using the following parts, which can b...

  14. How many wires are there in an NMEA 2000 cable?How many wires are there in an NMEA 2000 cable?
    An NMEA 2000 cable contains five wires, two for 12 volt power and ground, two for the data pair, and one shield wire.

  15. What is a powertap?What is a powertap?
    ...tap. The powertap is used to energize the 12 volt power and ground wires found within the NMEA 2000 cable.

  16. Should I use double ended cordsets or should I build my own cables using bulk cable and field attachable connectors?Should I use double ended cordsets or should I build my own cables using bulk cable and field attachable connectors?
    ...r molded double ended cordsets since they are less expensive and they tend to be more reliable than cables made using bulk cable and field attachable connectors. Unfortunately, over molded double ende...

  17. Does Maretron offer any recommendations for securing NMEA2000 cabling?Does Maretron offer any recommendations for securing NMEA2000 cabling?
    ...ant to ensure long term functionality and use. Illustration 1 provides a best practices of securing cable.

  18. What is an RAA100?What is an RAA100?
    The RAA100 is a rudder angle adapter that converts an analog resistive sender into digital information, which is then broadcast over the NMEA 2000 where any NMEA 2000 compatible display can show the r...

  19. What video system can be used with N2KView-Video?What video system can be used with N2KView-Video?
    ...ly supported: -Axis 209FD-R Network Camera. This is a low-profile camera powered over the Ethernet cable. -Axis 212 PTZ Network Camera. This is a wall-mounted camera with software pan Tilt and Zoom....

  20. What firmware changes have taken place on the Maretron ACM100 AC Monitor?What firmware changes have taken place on the Maretron ACM100 AC Monitor?
    What firmware changes have taken place on the Maretron ACM100 AC Monitor? Update your device today using the N2KAnalyzer software tool. ACM100 Firmware Versions 1.0.7 (2011-03-...

(Page 1 of 2)     «« |  Prev | 1 | 2 | Next | »»

Powered by Interspire Knowledge Manager Knowledgebase Software

HOME
PRODUCTS
SUPPORT
COMPANY
HOW TO BUY
© 2012 Maretron, LLP. All rights reserved.
Visit Carling Technologies, a partner company.